I recently found this link, a HOW TO for using the USB ports on the newer DirecTV Units with MythTV. I am NOT the owner of this article and have sent an email to the owner, Jeff Simpson, to let him know I was sharing this info with this site.
DirecTV supplies, and has supplied, a variety of set top boxes (referred to as "STB" from here on) to consumers. Nearly all of them have the ability, although not directly advertised, to be controlled from an external device, such as a MythTV BackEnd.
The D10 & RCA Satellite STB
Many of the older (pre 2007) STB's that were sold or leased by DirecTV have a small phone-style port on the back of the unit that is labeled as "Low Speed Data Port" or simply "Low Speed Data". This port, although it can be initially be mistaken as a standard RJ-11 phone jack, is actually quite a bit smaller (in technical terms, it is called an RJ-22) and is sometimes referred to as a "mini RJ-11" port. If you take a look at the coil handset cable on your non-cordless phone (you still have one of those, right?), you will see that the plug on that cord is the same as the port on the back of the STB.
You will need the following components in order to create a connection from your MythTV backend to the STB:
- a USB->Serial Adapter (USB Male to 9-pin Male) (eg: http://www.dtvcontrol.com/index.aspx?content=cable, which shows up under linux as "Prolific Technology, Inc. PL2303 Serial Port")
- a handset cord for a corded phone
- a Serial->RJ45 adapter
- a short length of ethernet cable with RJ-45 connectors already crimped down on each end
If you prefer to get your hands on a modular serial hood, you can omit the Serial->RJ45 adapter and the ethernet cable. I used the items listed above because that was what I had readily available.
The DirecTV D11/H20 Satellite STB
The DirecTV D11/H20 Satellite set top box contains a USB port that can be used as a serial port to change channels and perform other tasks on the box. To do this, you need the following cables:
- USB->Serial Adapter (usb male to 9 male).
- IOGEAR GUC232A, ATEN UC-232A (pl2303), BAFO BF-810, QVS UR-2000M2, Sabrent SBT-USC1M and other PL2303 based adapters are known working. Succesfully tested with:
- 13in Port Authority USB Serial DB9 Adapter Cable
- On July 06, 2007 it was reported that EMTC is no longer shipping Linux compatible (PL2303) cables. Previously, they were a good and inexpensive supplier, but the replacement cables are not compatible. DO NOT BUY THESE
- Other cables/adapters are unknown (use at your own risk).
- 9-pin Null-Modem Adapter (9 female to 9 female)
- 9 pin serial cable. (9 female to 9 male)
The end result of this is a null modem serial connection between computers. I assume that using two USB->Serial adapters would also work, (see note below) given that the Null Modem adapter was still used.
I used the BAFO BF-810 adapter (found for $9 online) and a pair of 9pin DSub to RJ45 adapters wired as a crossover serial cable, along with a straight-through ethernet cable.
I started with the directv.pl script used to control the D10 box. I had to change the speed to 115200 from 9600 (contrary to the installers guide which says 9600 or 155200, which must be a typo). I also had to enable hardware flow control in order to get reliable operation.
NOTE: I was using 115,200 baud for months with two D-11 boxes. Around the middle of January 2007 I started getting channel change failures. Switching it to 9600 baud fixed it. My theory is that DirecTV sent down a firmware upgrade to change the all the D-11 boxes to 9600.
NOTE: D11 and H20 boxes require baud rate = 115200.
NOTE: For Mac OS X connecting to a D11 or H20 use directv.pl ver 1.8 which supports baud rates (for Mac and Linux) >38400. A usb to serial adapter on both ends connected by a null modem cable works fine.
Making Your Own Custom Cable (D10/RCA)
You can either buy a cable to convert from the low speed data port to a serial port from DTVcontrol.com or, using the pinout either on that page or within this page (they are the same), you can make one on your own.
Overall difficulty of making your own cable is rather low. Take your time, and be prepared to test it once (or twice) before taping everything up to make sure you got it right.
Using the items listed aboce, I grabbed with the handset cable, two serial to RJ-45 adapters, and a short RJ-45 ethernet cable and I:
- Cut the headset cable in half, giving me two pieces of the same approx. length.
- Cut the RJ-45 cable in half giving me two pieces of the same approx. length.
- Cut back the outer sheathing on the RJ-45 cables at the point where I cut it in half.
- Cut back the outer sheathing on the headset cables at the point where I cut it half (this was a pain)
- Cut back the sheathing on the individual exposed wires on the RJ-45 cables and the headset cables.
- Plugged the RJ-45 cables in to the Serial-RJ45 adapters.
- Using a 9-volt battery and a cheap DC tester, I mapped out what pins on the serial side of the adapter mapped to which exposed wires on the cut end of the RJ45 cable. WRITE THEM DOWN. I cannot stress this enough. Because you will be dealing with two different wires, it is easy to get confused. I have these written down at home, and, after making my third adapter, I can tell you that the entire mapping is usually custom since serial-to-RJ45 adapters are not all created equal, the handset cables are not always color coded, and you can use any variant of RJ45 cabling.
- Using your mapping of the serial port adapter to the individual wires in the ethernet cable, write down the proper mapping of the wires from the handset cable to the individual wires of the ethernet cable.
- Following the mapping you just created, hand twist the appropriate wires together and use electrical tape to hold it.
Because I had the DC tester (with the little light on it), I was able to do a final test of the completed connection to confirm that the wires were connected properly. Connect the serial port end to either your MythTV backend's serial port, or, if you don't have one available (most machines now-a-days don't have more than two, and many only have one), plug it in to the USB->Serial port adapter, and plug the USB->Serial port adapter in to an available USB port. Plug the other end of the cable you just made (the mini RJ-11) in to the STB.
Now, test it and make sure it changes channels. /usr/local/bin/directv.pl setup_channel 10
If it does not work, you will get something on the command line like "excessive retries to port" or some similar error. This means, more than likely, that you reversed the mapping of the pins. I say this because that is exactly what I did. I had looked at the mini RJ11 port, and the exposed wires (all of the wires on the one that I had were the same color: gray!) and asked myself "Which end is pin 1?"
Custom Channel Change Configuration
In order to configure MythTV to call the directv.pl script, you must add the command with desired options to the tuner section of mythtv-setup (User Manual:Detailed configuration Backend).
- Run mythtv-setup
- Select Input connections
- Choose the connection you would like to control
- Add the script to the External channel change command parameter
For example, I set mine to...
The help text for this parameter says, "If specified, this command will be run to change the channel for inputs which have an external tuner device such as a cable box. The first argument will be the channel number." I interpreted this to mean that the channel will be added to whatever is specified here. This would mean that parameters could be added such as [hide, retries_number n,...]. It appears that once a command is sent like "hide" it is persistent. So you could specify it in a command window at any time.
Watch out for XWindows using the serial port by default
grigio # lsof /dev/ttyS0 COMMAND PID USER FD TYPE DEVICE SIZE NODE
NAME X 5479 root mem CHR 1,5 3943 /dev/ttyS0 grigio #
shows that X has the /dev/ttyS0 file open. We can fix this by commenting out the appropriate device section in your /etc/X11/xorg.conf file and restarting X.
Working around some missing functionality on the channel change script
In my situation, some of the features of the directv.pl script did not function in the way that I liked, or simply did not function with my STB. Specifically, with my STB, the "setup_channel" function, which is defined in the documentation as "turning the unit on, changing the channel, and hiding the on screen display" really only did the first two pieces, leaving the OSD up for an obscenely long amount of time. I simply wanted the script to change the channel and hide the OSD immediately.
While the directv.pl script can take the options out of order (eg: directv.pl port /dev/ttyUSB0 hide setup_channel 29), it did not seem to make any difference. This limitation required me to write a small wrapper script called "/usr/local/bin/change_channel.sh" :
#!/bin/shif [ "X$1" = "X" ] || [ "X$2" = "X" ]; then echo "Usage: $0 "
echo exit;fi/usr/local/bin/directv.pl port $1 setup_channel $2 hide
I then used "/usr/local/bin/change_channel" in the field as outlined above in the "Custom Channel Change Configuration" section. Be sure to specify the corresponding port for each of your tuners.
Mini RJ11 (RJ22 or 4P4C) Port Pinout:
Mini RJ11 (RJ22 or 4P4C) to Serial Port mapping
When everything is built, the pinout of the resulting cable should be:
|DB9 Pin 5||->||mini RJ11 Pin 1|
|DB9 Pin 2||->||mini RJ11 Pin 2|
|DB9 Pin 3||->||mini RJ11 Pin 4|
Null Modem Cable Pinout
This is a standard Null-modem cable, but here is the pinout for the sake of being complete:
|RTS||(Request To Send)||7||->||8||CTS|
|CTS||(Clear To Send)||8||->||7||RTS|
Serial -> RJ45 (Pin to Wire) Mapping
I used a standard SUN supplied serial to RJ45 adapter and got the following mapping of the serial port pins to the individual wires on the RJ45 cable plugged in to the serial port adapter. I also used a snort length of off-the-shelf pre-made RJ-45 (Cat5) wire.
|Serial Port||RJ45 (standard coloring)|
|5||Orange and Green/White|
- DirecTV D11-500: Channel changing works (by key). On/Off, OSD On/Off, Remote Input On/Off all work. Other features not working yet.
- DirecTV D11-300: Channel changing not yet confirmed, some problems reported
- DirecTV D11-100: Same results as D11-500.
- DirecTV D12: Same as D11-100. Except the D12 supports get_channel where the D11 does not.
- DirecTV H20: Same results as D11-500
- DirecTV D10
- Most DirecTV RCA STB's
Controlling D11 from Windows
I know this isn't Myth-related at all, but here is how to control the D11 from windows!
- Install Perl (I recommend [ActivePerl])
- Start Perl Package Manager (PPM)
- Add the BdP Repository: repository add BdP
- Install Win32::SerialPort: install Win32-SerialPort
- Install Win32::API: install Win32-API
- Install Time::HiRes: install Time-HiRes
- Download the Windows version of the DirecTV Serial Control Script (see links below). Save it to C:\perl\
- Example Execution:
perl.exe c:\perl\directv2.pl port com1 baudrate 115200 flow none box_type D11 25
- DirecTV D11 Users Manual
- DirecTV D10/D11 Installers Guide (Contains serial command guides)
- General Set-top Information for Installers V1.3 (Contains serial command guides)
- DirecTV Serial Control Script (directv.pl)
- Script modified to work with D11
- Windows Version of directv.pl
- D10/RCA Custom Cable information (including pinout)