InstantCake Instructions and Release Notes

Page 1 | Page 2

Introduction

InstantCake is a custom DIY software tool designed to quickly and easily create a basic replacement drive kit from a standard off-the-shelf PC hard drive. InstantCake comes as a single CD (or as a downloadable ISO which can be easily burned to CD) for your specific TiVo Digital Video Recorder. The CD must be booted from your PC's CD-ROM drive, and it will ask you several simple questions about the upgrade you wish to perform. InstantCake will then create a replacement drive kit on one or two standard hard drives that must also be connected to your PC. Your original TiVo hard drive is not used or required for the upgrade and we recommend you keep it in a safe place and use it as a backup in case anything goes wrong with the new drives you've created.

Requirements for using InstantCake

You will need an x86-based Personal Computer (PC) with two IDE interfaces which can be accessed as the PRIMARY and SECONDARY devices, and a CD-ROM which you can use to boot our CD. You do not need to be running Windows XP or any specialized software, in fact, we recommend you disconnect your hard disk drive(s) to ensure their protection, as well as disable any SATA devices supported on your motherboard. The InstantCake software boots and runs from a CD we supply you or can be burned if you've downloaded it as an ISO. You will need one or two blank hard drives which will be formatted for use in your TiVo. We do not recommend you use your existing TiVo disk drive for InstantCake installations, in fact, in many cases it will not work: the target drive is expected to be larger than the original - please keep your TiVo drive in a safe place as a backup; at least until you've used InstantCake successfully at least once.

Directions for using InstantCake

  • Step 1: Configure your PC such that your CD-ROM drive is connected as the primary slave device. You may need to adjust a jumper on the rear of the CD-ROM; many CD-ROM drives have the jumper set for cable-select (CS) and you can simply move the jumper to the slave position (SL) to ensure it is configured properly. To ensure the CD-ROM is connected as the primary IDE device, use the IDE cable connected to your PC's C drive; this is typically connected to the primary IDE interface in your PC. If you have more than one CD/DVD device in your system, please disconnect all but one of them. We recommend you disconnect your PC's primary hard drive (and any other hard drives that are installed in your PC) to ensure they are not accidentally overwritten by the InstantCake software.
  • Step 2: Configure your PC's system BIOS so that you can boot from CD-ROM, and ensure your CD-ROM is installed as the primary slave on your PC.
  • Step 3: Configure and connect one or two new drives destined for your TiVo on the PC's secondary IDE interface. You will need to refer to the manufacturer's guidelines for master and slave settings for your hard drives' jumpers. Do not use the cable-select jumper settings for your new drive(s); it is important to know which drive is the master and which drive (if you are building a dual-drive kit for your TiVo) is the slave to ensure they are properly installed in your TiVo.
  • Step 4: Apply power, and boot the InstantCake CD. The CD will auto-boot and prompt you with a few questions before building your kit.
  • Step 5: Please take note of all messages, warnings and instructions which may be displayed when the InstantCake program is done running. Knowing these important details may make a difference, especially if you need additional support.
  • Step 6: Install your new drives in your TiVo; you can use our hardware installation instructions as a reference.

[[page]]

Page 1 | Page 2

Release Notes and Additional Support Resources

Please refer to the release notes for your specific version of InstantCake before proceeding with your installation (see below for specifics).

We have designed InstantCake to be as easy-to-use as possible, however we cannot guarantee that it will work on your specific PC, as some older systems have trouble booting from CD, or may not have enough memory to load the InstantCake software properly. PTVupgrade is not responsible for InstantCake not working on your PC, or if you cannot get the software to work properly on your PC. If you are concerned about this possibility, please do not purchase the product.


 

Release Notes - InstantCake for Series1 Standalone Units

TiVo Models Supported

Philips PTV100, PTV300, HDR110, HDR112, HDR212, HDR312, HDR31201, HDR31202, HDR31203, HDR31204, HDR612
Sony SVR-2000

Release notes for this product are now maintained in our knowledgebase.


Release Notes - InstantCake for Series1 DirecTV TiVo Units

TiVo Models Supported

Philips DSR6000, DSR6000R, DSR6000R1
Sony SAT-T60
Hughes GXCEBOT, GXCEBOTD

Release notes for this product are now maintained in our knowledgebase.



Release Notes - InstantCake for Series2 Standalone Units

TiVo Models Supported

TiVo TCD130040, TiVo TCD140060, TiVo TCD230040
TiVo TCD240040, TCD24004A, TCD240080, TCD24008A, TCD240140
TiVo TCD240040, TCD24004A, TCD240080, TCD24008A, TCD240140
TiVo TCD540040, TCD540080, TCD540140
TiVo TCD649XXX
Sony SVR3000
HUMAX T800, T2500

Release notes for this product are now maintained in our knowledgebase.



Release Notes - InstantCake for Series2 Standalone Units with DVD players/recorders

TiVo Models Supported

Pioneer DVR-810HS

Pioneer DVR-57H
Humax DRT400 / DRT800
Toshiba SD-H400
Toshiba RS-TX20 / RS-TX60

Release notes for this product are now maintained in our knowledgebase.



Release Notes - InstantCake for Series2 DirecTV TiVo Units

TiVo Models Supported

Standard Definition Units

DirecTV R10
Hughes HDVR2, HDVR3, SD-DVR40, SD-DVR80, SD-DVR120
Philips DSR7000, DSR704, DSR708
RCA DVR39, DVR40, DVR80, DVR120
Samsung SIR-S4040R, SIR-S4080R, SIR-S4120R

High Definition Units

Hughes/DirecTV HR10-250

Important Note for PTVnet DIY CD users: To use InstantCake in conjunction with the PTVnet DIY CD, you MUST boot with the PTVnet DIY CD FIRST.

Release notes for this product are now maintained in our knowledgebase.